Solar Road Studs
Solar-powered road studs with LED or reflector bodies for lane and edge marking.

Reflective Road Stud
Passive reflective road stud for lane and edge marking: cast aluminium body, prismatic reflectors, no battery or solar panel. Bonded or anchored to the road.
Solar LED Road Stud
Solar LED road stud with a self-contained panel and replaceable battery. Flashing or steady, aluminium body, adhesive or cast-in mounting.Specification parameters
1. Product Range
| Surface-Mount Solar Stud | Aluminium body bonded to the road surface with epoxy |
|---|---|
| Shank (Cast-In) Solar Stud | Aluminium body with stem, set in a cored hole |
| Single / Double-Sided | LEDs on one or both faces |
| Built-In Reflectors | Retroreflectors recessed in the aluminium shell |
2. Body & Dimensions
| Body Size | 100 – 125 mm × 97 – 107 mm × 20 – 26 mm |
|---|---|
| Stem | 45 – 50 mm |
| Body Material | Die-cast aluminium alloy (ADC12) |
| Lens | PC or PMMA |
3. LED & Visibility
| LEDs | Ø5 mm high-brightness LEDs; 4 – 6 per stud, double-sided |
|---|---|
| LED Colour | White, yellow, red, blue, green |
| Mode | Flashing at approx. 2 Hz, or steady |
| Switching | Photoelectric switch: on at dusk or in poor weather |
| Visible Distance (supplier data) | > 800 m at night |
| GB/T 24725-2024 LED Requirement | ≥ 3 LEDs per face; each ≥ 6000 mcd at rated current; half-intensity angle ≥ 15° |
4. Solar Power & Battery
| Solar Panel | Monocrystalline; 2 – 2.5 V for Ni-MH; 5 V for lithium |
|---|---|
| Battery | Ni-MH 1.2 V 600 mAh, or lithium 3.2 V 500 mAh |
| Charge Time | Approx. 8 h to full charge |
| Run Time on Full Charge | Approx. 70 – 140 h flashing; approx. 40 h steady |
| Battery Life (supplier data) | Ni-MH 2 – 3 years; lithium up to 5 years |
5. Load, Ingress & Environment
| Ingress Protection | IP68 |
|---|---|
| Static Load | 20 t; > 30 t on reinforced models |
| Operating Temperature | From −20 °C to +70 °C, up to −39 °C to +80 °C, by model |
| ASTM D4280 Compressive Test | 6000 lbf (26.7 kN) load; deformation < 3.3 mm |
| ASTM D4280 Flexural Test | 2000 lbf (8.9 kN) without breakage |
6. Installation
| Shank Models | Core-drill Ø35 mm × 55 mm deep, fill with epoxy, set the stud |
|---|---|
| Surface Models | Clean, flat surface; epoxy applied evenly to the stud base |
| Curing | Keep traffic off for 6 – 8 h |
| Spacing — Highways | Approx. 5 – 6 m |
| Spacing — Hazardous Entrances / Exits | Approx. 2 – 3 m |
| Spacing — Parking & Access Roads | Approx. 0.5 – 2 m |
7. Standards
| China | GB/T 24725-2024 Raised pavement markers (replaces GB/T 19813-2005 Solar raised pavement markers from 2024-12-01) |
|---|---|
| Europe | EN 1463-1:2021, EN 1463-2:2021 (retroreflecting road studs; active studs not covered) |
| EN 1463-1 Stud Types | Type A non-depressible, Type B depressible; reflector Type 1 glass, Type 2 plastic, Type 3 abrasion-resistant plastic |
| EN 1463-1 Minimum R (white, ±5° / 0.3°) | 20 / 220 / 150 mcd·lx⁻¹ for reflector Types 1 / 2 / 3 |
| USA | ASTM D4280 raised retroreflective pavement markers |
8. Applications
| Highways & Urban Roads | Lane and edge lines |
|---|---|
| Entrances & Exits | Ramps, junctions and hazardous approaches |
| Parking & Access | Parking lots, hospital and facility access roads |
| Pedestrian Areas | Steps and pedestrian pathways |