Get Free Quote

Lamp Poles

Solar and mains street lighting columns, including camera and signage arms.

Specification parameters

1. Product Range

Single-Arm Street Lighting ColumnResidential and urban roads; conical, octagonal or round shaft
Double-Arm Street Light PoleWide roads, dual carriageways and major intersections
Solar Street Light PoleColumn with top panel bracket; 6 – 8 m poles typically carry 20 – 30 kg of panel and luminaire
Post-Top ColumnLantern mounted on the column top; EN 40-2 covers post-top columns up to 20 m

2. Column Dimensions

Height6 / 8 / 10 / 12 m typical for roads; EN 40-2 nominal post-top heights 3 – 20 m, bracketed columns up to 18 m
ShapeConical (most common), octagonal (bent plate), round or polygonal
Top / bottom diameterApprox. 60 – 140 mm top and 140 – 300 mm bottom across 6 – 12 m columns (supplier reference tables)
Wall thickness3.0 mm (6 m) to 4.0 – 5.0 mm (12 m); heavier sections for taller or high-wind designs
ArmSingle or double; projection 0.5 – 3.0 m; rise typically 5 – 15°; luminaire spigot 35 – 60 mm
Bracket projection guidanceEN 40-2 recommends projection ≤ h/4; UK highway practice: lesser of 0.25 × height or 3 m
Longitudinal seamAutomatic submerged-arc welding (supplier data)

3. Base, Door & Cable Entry

Base plateApprox. 300 × 300 × 16 mm (6 m) to 400 × 400 × 20 mm – 500 × 500 × 25 mm (12 m); final size by structural calculation
Anchor bolts4 × M20 (6 m) to 4 × M24 – M27 (10 – 12 m); hot-dip galvanized J-bolts with template
Foundation depthApprox. 0.8 – 1.2 m for small poles, 1.2 – 2 m for medium poles
Door opening (EN 40-2)Protection IP3X for doors and parts up to 2.5 m; compartment door impact test IK08
Cableways (EN 40-2)Min. Ø 18 mm from base to lantern; min. Ø 50 mm from cable entry to base

4. Material

Chinese GBQ235B, Q355B (formerly Q345B)
European (EN 40-5)Sheet and plate to EN 10025 (S185 excluded), e.g. S235JR, S355JR; hot-finished tube EN 10210; cold-formed tube EN 10219; stainless EN 10088
American ASTMA36; A572 high-strength option
Foundation bolts (EN 40-5)Minimum mechanical properties of EN 10025 grade S235JR

5. Surface Treatment

Hot-dip galvanizingInside and outside of the shaft; to ISO 1461 or ASTM A123
ASTM A123 (pipe & tubing)75 µm minimum average for 3.2 mm wall and above
Powder coatingOptional duplex system: galvanizing + polyester powder coat in RAL colours
EN 40-5 protection zonesArea A outside from top to ≥ 0.2 m above ground; Area B ground section incl. ≥ 0.25 m above ground; Area C inside

6. Structural Design Basis

EN 40-3-1 / 3-2 / 3-3Characteristic loads (wind, lantern, bracket); verification by testing (3-2) or by calculation (3-3) at the site reference wind velocity
AASHTO LRFD LTSBasic wind speed set by mean recurrence interval (10 / 300 / 700 / 1700 years) according to traffic volume and risk category
AASHTO example (Iowa DOT)1700-year MRI, 53.6 m/s (120 mph) for Extreme I; 10-year MRI, 34.0 m/s (76 mph) for Service I
AASHTO fatigue loadsGalloping, vortex shedding, natural wind gust and truck-induced gust, scaled by a fatigue importance factor
Supplier wind ratings30 – 40 m/s for standard areas; 45 – 60 m/s for coastal areas; or to site data
Passive safety (EN 12767)Non-energy-absorbing, low-energy-absorbing or high-energy-absorbing categories, where columns stand in the clear zone

7. Standards

EuropeEN 40-2, EN 40-3-1, EN 40-3-2, EN 40-3-3, EN 40-5; EN 12767
USAAASHTO LRFD Specifications for Structural Supports for Highway Signs, Luminaires, and Traffic Signals; ASTM A123
GalvanizingISO 1461; GB/T 13912 (China)
Quality SystemISO 9001